2008年 第22卷 第6期
石 油 仪 器
PETROLEUM INSTRUMENTS
1
开发设计
48道高精度地震仪器研发
潘中印 梁保江 杨恒辉 薛慧珍 张永学
(东方地球物理公司装备制造事业部西安物探装备分公司 陕西西安)
摘 要:高采样率、小道数地震仪(24~240道) 是一种广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域的一种十分通用的地震勘探仪器。文章针对大型勘探地震仪器对于小规模工程勘探, 不仅勘探费用无法承受外, 以及工程勘探多在山区使用和大型仪器也无法到位这一实际情况和不适用性, 介绍了48道高精度地震仪研发过程, 较详细论述了其系统原理、系统设计和样机试制。该仪器轻便、操作简单、功耗低, 稳定性、可靠性相对较高, 具有良好的性能价格比, 具有广阔市场的需求量。关键词:48道; 地震仪; 高精度
中图法分类号:P 631. 4+35 文献标识码:B 文章编号:1004 9134(2008) 06 0001 03
0 引 言
我国20世纪的七、八十年代的地震勘探仪器以24道、48道为主, 并逐渐发展到120道模拟勘探仪器。随着勘探技术的发展, 勘探仪器逐步从模拟传输到数字传输, 小道数发展到今天的大道数(10000道) 。随着仪器性能的提高, 道数的增大, 制造成本也在增大, 相应的勘探成本也在提高。随着物探领域内勘探方法向多样化发展, 处理的技术和方法也在不断提高[1]。一种广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域的十分通用的高采样率的小工程勘探仪器的需求也在不断加强。针对大型勘探地震仪器对于小规模工程勘探, 不仅勘探费用无法承受且工程勘探多在山区, 大型仪器也无法到位, 而现有的GDZ24高精度工程地震仪因道数少(24道) , 采样率低
(最高1/4ms 采样) , 已不能满足市场的需要。为了适应市场需求, 满足用户需要, 提高市场占有率, 西安物探装备分公司研制开发了48道高精度地震仪。本文介绍了48道高精度地震仪研究目标、主要内容及工作原理和技术指标。
1 系统研究目标和主要内容
3]1. 1 研究目标[2、
国内外同类仪器生产厂家有西安物探装备分公司(GDZ24A) 、美国GEOMETRIC 公司(SV-NX) 、重庆奔腾数控技术研究所(WZ24/48A) 等。主要技术指标对比见表1。
综合性能分析, 多道数、轻便、小型工程地震仪具有重要意义:1) 道数的增多, 减少施工炮数, 节约成本; 2) 增加勘探施工面积, 提高勘探深度; 3) 提高采样率,
表1 几种小道数地震仪性能对比表
主要技术指标系统道容量采样间隔采样点数频率响应记录格式A/D转换器动态范围
美国SV-NX 工程地震仪
12~72 250 s ! 16K 样点/道0. 3Hz~1700Hz SEG-D, SEGY
24位 144dB
重庆WZG-24/48A 工程地震仪
24/48 10 s ! 16K 样点/道0. 1Hz~4000Hz
SEG-224位 144dB
西安GDZ24A 工程地震仪
24 250 s ! 16K 样点/道3Hz ~1600Hz
SEG-224位 144dB
第一作者简介:潘中印, 男, 1962年生, 教授级高工, 1983年毕业于江汉石油学院地球物理专业, 现在东方地球物理勘探公司西安物探装备分公司
从事技术科研管理工作。邮编:710082
2
石 油 仪 器
PE T ROLEUM INSTRUMENTS
2008年12月
增加了勘探分辨率。因此, 确定研制目标为:研制与国外同类产品性能相当、可扩展的多道工程地震仪器。系统最高采样率达到125us 、实时地震道数48道。使得该仪器不但可以用于石油勘探中的小折射、微测井, 还可用于二维地震反射波、面波等工程勘探领域。1. 2 主要内容
同大型地震数据采集系统相比, 小道数地震仪器采用集中式结构设计便于数据传输和实现实时地震监视。但其主要的研制内容如下:
1) 实时48道高速数据传输及数据编排技术; 2) 高采样率数据采集板设计开发;
3) 控制软件:系统管理、数据采集、存储、处理、显示、实时监视记录、绘图等;
4) 系统测试软件开发:包括系统自检、检波器测试等功能;
5) 机械及电工艺的可靠性设计开发。
根据上述主要研究内容, 并遵照仪器要轻便灵活、技术先进的原则, 确定了开发该仪器系统的技术关键将集中在:一是高采样率、24位 ~ 高精度模/数转换技术应用; 二是多种接口技术, 即人机交互接口、PCI 、FPDP 等高速数据传输接口和多种震源接口技术的设计和应用; 三是实时相关处理/滤波技术、数据编排技术的应用。
CPU 板选用超低功耗、高速度(600MHz) PC104+板卡, 与用户板采用无背板插针式连接, 通过PCI 总线对用户板进行控制及数据交换;
控制板由PCI 接口电路、震源接口电路、高精度信号发生器、温度及电源检测电路、数据传输电路、DSP 数据处理电路、数据缓存电路、逻辑控制电路等几部分组成。其主要功能为:
1) 通过PCI 总线接口对采集通道进行参数设置;
2) 发出∀点火#指令, 启动系统数据采集; 接收∀时断#、∀井口#信号以及可控震源的扫频信号;
3) 经由数据传输接口接收48个采集通道数据并按道序编排;
4) 对可控震源的扫频信号与48个采集通道数据实时相关处理;
5) 采样率低于4kHz 时, 对采集数据进行抽取滤波处理;
6) 数据道与辅助道数据通过PCI 总线读到CPU 板内存并记盘;
7) 为通道板提供高精度测试信号; 8) 温度及供电电源检测。
两块通道板。每24道模拟信号对应一块通道板, 主要完成输入道覆盖滚动、大线滤波, 信号放大(每道增益可分别设置0dB, 18dB, 36dB 或42dB) 、摸数转换和通过测试开关选择输入通道处于正常采集或测试状态。可进行的测试项包括:检波器噪音测试、道一致性测试、增益精度测试、脉冲测试、内噪音测试、串音测试、共模测试、畸变测试。
2. 2 主要技术指标
通道数:单板24道, 总道数48道
模数转换器: ~ 24位
采样率:15. 625 s 、31. 25 s 、62. 5 s 、0. 125ms 、0. 25ms 、0. 5ms 、1ms 、2ms 、4ms 、8ms 、16ms 前置放大器增益:0dB 、18dB 、36dB 、42dB, 每道可单独设置
记录长度:标准16384样点, 65536样点可选噪音:
串音:100dB
存贮介质选用活动硬盘或内部系统盘, 通过USB 接口导出数据。其他外设接口包括2个USB2. 0接口, 2个以太网口, 串口等。
显示器采用12. 1in(1in=25. 4mm) 宽温液晶屏、触摸屏, 输入用软键盘。
2 系统设计与实现
为便于实时地震监视、减少野外电子设备数量, 仪器系统采用∀集中式#设计。即:来自地震检波器的模拟地震信号, 经由模拟地震电缆传输直接进入系统主机, 完成模拟信号滤波、放大、AD 转换, 经数据格式编排以SEG-2格式记录在硬盘或其它介质上, 并可以硬拷贝的形式打印出来。
2. 1 系统组成和原理
工作原理框图如图1所示。该仪器系统主要有由CPU 板、控制板、两块采集通道板, 电源板、存储介质、显示器、
小型绘图仪和其它外设接口等组成。
图1 系统工作原理框图
工
2008年 第22卷 第6期 潘中印等:48道高精度地震仪器研发 3
LTPV4454in 热敏打印机。系统由12V 直流电瓶供电, 电源板产生系统需要的12V 、+5V 、∃5V 、3. 3V 等几组电源, 通过背板接插件送到各板及打印机与显示屏、硬盘等部件。2. 3 软、硬件平台及开发工具
基于PPC104PLUS 系统硬件平台, 应用软件对系统硬件的访问(主要是对PCI 总线) 是通过运行于Windows XP 上的C ++Builder 和Windriver 8. 11来实现的, 系统软件平台如图2
所示。
2. 5 系统测试
系统可设置不同的采样率(2ms 、1ms 、0. 5ms 、0. 25ms 、0. 125ms 、0. 0625ms) 和前放增益(18dB, 36dB, 42dB) 。在不同的采样率和前放增益条件下, 对系统进行脉冲响应一致性、增益精度、等效输入噪声、道间串音、共模抑制比和总谐波畸变进行测试, 测试结果达到了设计要求。
3 结 论
西安物探装备分公司已基本研制完成了48道高精度工程地震仪科研样机, 通过了室内系统模拟指标测试, 系统样机经过野外实际施工和对比试验及可靠性测试, 各项指标均达到设计要求。48道高精度工程地震仪的研制成功为广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域提供了一种十分通用的高采样率的小工程勘探仪器。
图2 系统软件平台
2. 4 机械结构设计
在现有24道仪器结构基础上, 参考同类仪器机械设计, 做到了装配、拆卸、维护方便, 美观结实, 适应野外操作。如, 为适应野外阳光下直视操作, 设计为上翻盖箱体, 显示屏可90%转角; 大线输入插头及其它外设接口、打印机出纸口设置在箱体侧面, 球型鼠标、触摸键盘设置在面板上。
参考文献
[1] [美]GEOMET RIC 公司. SV -NX 工程地震仪使用说明
书. 2006(资料)
[2] 重庆奔腾数控技术研究所. WZ24/48A 工程地震仪使用
说明书. 2007(资料)
[3] 沈兰荪. 数据采集技术[M ]. 安徽:中国科技大学出版
社, 1989
(收稿日期:2008-09-22 编辑:梁保江)
&石油仪器∋编辑部迁址通知
&石油仪器∋编辑部自2009年起搬至新址办公:
西安市劳动路115号&石油仪器∋编辑部 邮编:710082
联系电话:029-68555093(传真) 68555094 投稿信箱及修改稿信箱不变。
原办公地址及所有办公电话即日起停止使用。
&石油仪器∋编辑部
Vol. 22No. 6 PETROLEUM INSTRUMENTS ∗
ABSTRACTS
Vol. 22No. 6Dec. 2008
Pan Zhongyin, Liang Baojiang, Yang Henhui, Xue Huizhen and Zhang Yongxue. Development of 48-channel high accuracy seismic instrument. PI, 2008, 22(6) :1~3
The paper introduces a new type of 48-channel engineering seismic instrument, and describes its principle and characteristics.
Key words:48-channel; seismic instrument; high accuracy
Zhang Jiatian, Huang Weisen, Yan Zhengguo, Wu Yinchuan and Zhang Yuying. Design of the extremely low frequency signal source based on the cased hole formation resistivity. PI, 2008, 22(6) :4~6
In order to improve the frequency stability of the extremely low frequency signal source, the DDS (Direct Digital Synthesizer ) technology is adopted to design the extremely low frequency signal source by the DDS chip named AD9834and the MC U named C8051F020, and the method of hardware and software are given. The result indicates that the sig nal source (frequency and the frequency stability all met the requirement of the cased hole formation resistivity. Key words:cased hole formation resistivity; signal source; AD9834; C8051F020
Cai Chaopeng, Yu Yingjiao, Zhang Rui, Shen Jianguo and Zhan Baoping. Experimental research on the liquid density measurement by acoustic wave method. PI, 2008, 22(6) :7~9
Acoustic wave is ex cited by an acoustic source in the side of a plate which is in different kinds of liquid in density and viscosity. It transmits along the plate and is coupled to liquid through the upper and low er interfaces of the plate. The transmission of the acoustic wave varies in velocity and amplitude according to the density, velocity and viscosity of the liquid. The characteristic of the liquid ) s density and velocity can be calculated by measuring the change of the veloc ity of the acoustic wave transmitting along the interface between the liquid and the plate according to frequency. This pa per researches the problem with the experimental method as follow :put a plate into two kinds of liquid with different density , measure the waveforms, compare the changes of the velocity of the waveforms according to frequency, show the difference between the waveforms measured in the two kinds of liquid directly. Key words:acoustic wave; liquid; density ; velocity
Guo Bin. Skateboard construction design of lith density logging tool. PI, 2008, 22(6) :10~11, 14
Based on drawing lessons from domestic and overseas experience on the machinery structure of the skateboard, a perfect system entirety construction is designed. The length is shorten from 1200mm to 840mm, this improves probe measurement effect.
Key words:lith density; skateboard; windows; pressure seal; integrated install
Lv Yanzong and Sui Guizhi. Method of wellhead time measurement in petroleum seismography technology. PI, 2008, 22(6) :12~14
The author analyzes the demerit of the currently method of measure wellhead time, after knows the characteristic of w ellhead time in petroleum seismography technology. A new method of measure wellhead time is put forward in the pa per , which can resist the noise , the change of signal, and calculate the time accurately. The new method have these character, such as few calculate, easy programming. The method of noise suppression is introduced also in the paper. Key words:petroleum seismography; wellhead time; sample method; reverse zero based noise threshold; noise suppres sion
Yu Yingjiao, Shen Jianguo, Song Gongpu and Li Shansheng. An experiment about shear wave transducer for the cross dipole sonic logging. PI, 2008, 22(6) :15~17
The transducer which can emit lower frequency vibration is an important part of the cross dipole apparatus. There are four vibration parts which mounded in cross dipole sonic logging and the distribution follows some regular in the transducer. So, detecting the vibration parts correctly will make sure that they can meet the final request. The paper de signs an experiment to research the problem. By stimulating the acoustic transducer made in Tianjin University, w e can get a acoustic field which follows some regular. From the FFT results of waveforms, we can get component of which the frequency is mainly between 500~800kHz. And the component varies according to the angle of the cross dipole appara tus.
Key words:cross dipole; sonic well logg ing; probe; acoustic
Jia Xiangdong , Liu Guoquan, Dong Bin, Chen Guangjian, Ling Bing, Bi Yuexin. Application of high resolu
2008年 第22卷 第6期
石 油 仪 器
PETROLEUM INSTRUMENTS
1
开发设计
48道高精度地震仪器研发
潘中印 梁保江 杨恒辉 薛慧珍 张永学
(东方地球物理公司装备制造事业部西安物探装备分公司 陕西西安)
摘 要:高采样率、小道数地震仪(24~240道) 是一种广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域的一种十分通用的地震勘探仪器。文章针对大型勘探地震仪器对于小规模工程勘探, 不仅勘探费用无法承受外, 以及工程勘探多在山区使用和大型仪器也无法到位这一实际情况和不适用性, 介绍了48道高精度地震仪研发过程, 较详细论述了其系统原理、系统设计和样机试制。该仪器轻便、操作简单、功耗低, 稳定性、可靠性相对较高, 具有良好的性能价格比, 具有广阔市场的需求量。关键词:48道; 地震仪; 高精度
中图法分类号:P 631. 4+35 文献标识码:B 文章编号:1004 9134(2008) 06 0001 03
0 引 言
我国20世纪的七、八十年代的地震勘探仪器以24道、48道为主, 并逐渐发展到120道模拟勘探仪器。随着勘探技术的发展, 勘探仪器逐步从模拟传输到数字传输, 小道数发展到今天的大道数(10000道) 。随着仪器性能的提高, 道数的增大, 制造成本也在增大, 相应的勘探成本也在提高。随着物探领域内勘探方法向多样化发展, 处理的技术和方法也在不断提高[1]。一种广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域的十分通用的高采样率的小工程勘探仪器的需求也在不断加强。针对大型勘探地震仪器对于小规模工程勘探, 不仅勘探费用无法承受且工程勘探多在山区, 大型仪器也无法到位, 而现有的GDZ24高精度工程地震仪因道数少(24道) , 采样率低
(最高1/4ms 采样) , 已不能满足市场的需要。为了适应市场需求, 满足用户需要, 提高市场占有率, 西安物探装备分公司研制开发了48道高精度地震仪。本文介绍了48道高精度地震仪研究目标、主要内容及工作原理和技术指标。
1 系统研究目标和主要内容
3]1. 1 研究目标[2、
国内外同类仪器生产厂家有西安物探装备分公司(GDZ24A) 、美国GEOMETRIC 公司(SV-NX) 、重庆奔腾数控技术研究所(WZ24/48A) 等。主要技术指标对比见表1。
综合性能分析, 多道数、轻便、小型工程地震仪具有重要意义:1) 道数的增多, 减少施工炮数, 节约成本; 2) 增加勘探施工面积, 提高勘探深度; 3) 提高采样率,
表1 几种小道数地震仪性能对比表
主要技术指标系统道容量采样间隔采样点数频率响应记录格式A/D转换器动态范围
美国SV-NX 工程地震仪
12~72 250 s ! 16K 样点/道0. 3Hz~1700Hz SEG-D, SEGY
24位 144dB
重庆WZG-24/48A 工程地震仪
24/48 10 s ! 16K 样点/道0. 1Hz~4000Hz
SEG-224位 144dB
西安GDZ24A 工程地震仪
24 250 s ! 16K 样点/道3Hz ~1600Hz
SEG-224位 144dB
第一作者简介:潘中印, 男, 1962年生, 教授级高工, 1983年毕业于江汉石油学院地球物理专业, 现在东方地球物理勘探公司西安物探装备分公司
从事技术科研管理工作。邮编:710082
2
石 油 仪 器
PE T ROLEUM INSTRUMENTS
2008年12月
增加了勘探分辨率。因此, 确定研制目标为:研制与国外同类产品性能相当、可扩展的多道工程地震仪器。系统最高采样率达到125us 、实时地震道数48道。使得该仪器不但可以用于石油勘探中的小折射、微测井, 还可用于二维地震反射波、面波等工程勘探领域。1. 2 主要内容
同大型地震数据采集系统相比, 小道数地震仪器采用集中式结构设计便于数据传输和实现实时地震监视。但其主要的研制内容如下:
1) 实时48道高速数据传输及数据编排技术; 2) 高采样率数据采集板设计开发;
3) 控制软件:系统管理、数据采集、存储、处理、显示、实时监视记录、绘图等;
4) 系统测试软件开发:包括系统自检、检波器测试等功能;
5) 机械及电工艺的可靠性设计开发。
根据上述主要研究内容, 并遵照仪器要轻便灵活、技术先进的原则, 确定了开发该仪器系统的技术关键将集中在:一是高采样率、24位 ~ 高精度模/数转换技术应用; 二是多种接口技术, 即人机交互接口、PCI 、FPDP 等高速数据传输接口和多种震源接口技术的设计和应用; 三是实时相关处理/滤波技术、数据编排技术的应用。
CPU 板选用超低功耗、高速度(600MHz) PC104+板卡, 与用户板采用无背板插针式连接, 通过PCI 总线对用户板进行控制及数据交换;
控制板由PCI 接口电路、震源接口电路、高精度信号发生器、温度及电源检测电路、数据传输电路、DSP 数据处理电路、数据缓存电路、逻辑控制电路等几部分组成。其主要功能为:
1) 通过PCI 总线接口对采集通道进行参数设置;
2) 发出∀点火#指令, 启动系统数据采集; 接收∀时断#、∀井口#信号以及可控震源的扫频信号;
3) 经由数据传输接口接收48个采集通道数据并按道序编排;
4) 对可控震源的扫频信号与48个采集通道数据实时相关处理;
5) 采样率低于4kHz 时, 对采集数据进行抽取滤波处理;
6) 数据道与辅助道数据通过PCI 总线读到CPU 板内存并记盘;
7) 为通道板提供高精度测试信号; 8) 温度及供电电源检测。
两块通道板。每24道模拟信号对应一块通道板, 主要完成输入道覆盖滚动、大线滤波, 信号放大(每道增益可分别设置0dB, 18dB, 36dB 或42dB) 、摸数转换和通过测试开关选择输入通道处于正常采集或测试状态。可进行的测试项包括:检波器噪音测试、道一致性测试、增益精度测试、脉冲测试、内噪音测试、串音测试、共模测试、畸变测试。
2. 2 主要技术指标
通道数:单板24道, 总道数48道
模数转换器: ~ 24位
采样率:15. 625 s 、31. 25 s 、62. 5 s 、0. 125ms 、0. 25ms 、0. 5ms 、1ms 、2ms 、4ms 、8ms 、16ms 前置放大器增益:0dB 、18dB 、36dB 、42dB, 每道可单独设置
记录长度:标准16384样点, 65536样点可选噪音:
串音:100dB
存贮介质选用活动硬盘或内部系统盘, 通过USB 接口导出数据。其他外设接口包括2个USB2. 0接口, 2个以太网口, 串口等。
显示器采用12. 1in(1in=25. 4mm) 宽温液晶屏、触摸屏, 输入用软键盘。
2 系统设计与实现
为便于实时地震监视、减少野外电子设备数量, 仪器系统采用∀集中式#设计。即:来自地震检波器的模拟地震信号, 经由模拟地震电缆传输直接进入系统主机, 完成模拟信号滤波、放大、AD 转换, 经数据格式编排以SEG-2格式记录在硬盘或其它介质上, 并可以硬拷贝的形式打印出来。
2. 1 系统组成和原理
工作原理框图如图1所示。该仪器系统主要有由CPU 板、控制板、两块采集通道板, 电源板、存储介质、显示器、
小型绘图仪和其它外设接口等组成。
图1 系统工作原理框图
工
2008年 第22卷 第6期 潘中印等:48道高精度地震仪器研发 3
LTPV4454in 热敏打印机。系统由12V 直流电瓶供电, 电源板产生系统需要的12V 、+5V 、∃5V 、3. 3V 等几组电源, 通过背板接插件送到各板及打印机与显示屏、硬盘等部件。2. 3 软、硬件平台及开发工具
基于PPC104PLUS 系统硬件平台, 应用软件对系统硬件的访问(主要是对PCI 总线) 是通过运行于Windows XP 上的C ++Builder 和Windriver 8. 11来实现的, 系统软件平台如图2
所示。
2. 5 系统测试
系统可设置不同的采样率(2ms 、1ms 、0. 5ms 、0. 25ms 、0. 125ms 、0. 0625ms) 和前放增益(18dB, 36dB, 42dB) 。在不同的采样率和前放增益条件下, 对系统进行脉冲响应一致性、增益精度、等效输入噪声、道间串音、共模抑制比和总谐波畸变进行测试, 测试结果达到了设计要求。
3 结 论
西安物探装备分公司已基本研制完成了48道高精度工程地震仪科研样机, 通过了室内系统模拟指标测试, 系统样机经过野外实际施工和对比试验及可靠性测试, 各项指标均达到设计要求。48道高精度工程地震仪的研制成功为广泛应用于石油、地质、煤层、桥梁建设、建筑、铁路和考古等工程领域提供了一种十分通用的高采样率的小工程勘探仪器。
图2 系统软件平台
2. 4 机械结构设计
在现有24道仪器结构基础上, 参考同类仪器机械设计, 做到了装配、拆卸、维护方便, 美观结实, 适应野外操作。如, 为适应野外阳光下直视操作, 设计为上翻盖箱体, 显示屏可90%转角; 大线输入插头及其它外设接口、打印机出纸口设置在箱体侧面, 球型鼠标、触摸键盘设置在面板上。
参考文献
[1] [美]GEOMET RIC 公司. SV -NX 工程地震仪使用说明
书. 2006(资料)
[2] 重庆奔腾数控技术研究所. WZ24/48A 工程地震仪使用
说明书. 2007(资料)
[3] 沈兰荪. 数据采集技术[M ]. 安徽:中国科技大学出版
社, 1989
(收稿日期:2008-09-22 编辑:梁保江)
&石油仪器∋编辑部迁址通知
&石油仪器∋编辑部自2009年起搬至新址办公:
西安市劳动路115号&石油仪器∋编辑部 邮编:710082
联系电话:029-68555093(传真) 68555094 投稿信箱及修改稿信箱不变。
原办公地址及所有办公电话即日起停止使用。
&石油仪器∋编辑部
Vol. 22No. 6 PETROLEUM INSTRUMENTS ∗
ABSTRACTS
Vol. 22No. 6Dec. 2008
Pan Zhongyin, Liang Baojiang, Yang Henhui, Xue Huizhen and Zhang Yongxue. Development of 48-channel high accuracy seismic instrument. PI, 2008, 22(6) :1~3
The paper introduces a new type of 48-channel engineering seismic instrument, and describes its principle and characteristics.
Key words:48-channel; seismic instrument; high accuracy
Zhang Jiatian, Huang Weisen, Yan Zhengguo, Wu Yinchuan and Zhang Yuying. Design of the extremely low frequency signal source based on the cased hole formation resistivity. PI, 2008, 22(6) :4~6
In order to improve the frequency stability of the extremely low frequency signal source, the DDS (Direct Digital Synthesizer ) technology is adopted to design the extremely low frequency signal source by the DDS chip named AD9834and the MC U named C8051F020, and the method of hardware and software are given. The result indicates that the sig nal source (frequency and the frequency stability all met the requirement of the cased hole formation resistivity. Key words:cased hole formation resistivity; signal source; AD9834; C8051F020
Cai Chaopeng, Yu Yingjiao, Zhang Rui, Shen Jianguo and Zhan Baoping. Experimental research on the liquid density measurement by acoustic wave method. PI, 2008, 22(6) :7~9
Acoustic wave is ex cited by an acoustic source in the side of a plate which is in different kinds of liquid in density and viscosity. It transmits along the plate and is coupled to liquid through the upper and low er interfaces of the plate. The transmission of the acoustic wave varies in velocity and amplitude according to the density, velocity and viscosity of the liquid. The characteristic of the liquid ) s density and velocity can be calculated by measuring the change of the veloc ity of the acoustic wave transmitting along the interface between the liquid and the plate according to frequency. This pa per researches the problem with the experimental method as follow :put a plate into two kinds of liquid with different density , measure the waveforms, compare the changes of the velocity of the waveforms according to frequency, show the difference between the waveforms measured in the two kinds of liquid directly. Key words:acoustic wave; liquid; density ; velocity
Guo Bin. Skateboard construction design of lith density logging tool. PI, 2008, 22(6) :10~11, 14
Based on drawing lessons from domestic and overseas experience on the machinery structure of the skateboard, a perfect system entirety construction is designed. The length is shorten from 1200mm to 840mm, this improves probe measurement effect.
Key words:lith density; skateboard; windows; pressure seal; integrated install
Lv Yanzong and Sui Guizhi. Method of wellhead time measurement in petroleum seismography technology. PI, 2008, 22(6) :12~14
The author analyzes the demerit of the currently method of measure wellhead time, after knows the characteristic of w ellhead time in petroleum seismography technology. A new method of measure wellhead time is put forward in the pa per , which can resist the noise , the change of signal, and calculate the time accurately. The new method have these character, such as few calculate, easy programming. The method of noise suppression is introduced also in the paper. Key words:petroleum seismography; wellhead time; sample method; reverse zero based noise threshold; noise suppres sion
Yu Yingjiao, Shen Jianguo, Song Gongpu and Li Shansheng. An experiment about shear wave transducer for the cross dipole sonic logging. PI, 2008, 22(6) :15~17
The transducer which can emit lower frequency vibration is an important part of the cross dipole apparatus. There are four vibration parts which mounded in cross dipole sonic logging and the distribution follows some regular in the transducer. So, detecting the vibration parts correctly will make sure that they can meet the final request. The paper de signs an experiment to research the problem. By stimulating the acoustic transducer made in Tianjin University, w e can get a acoustic field which follows some regular. From the FFT results of waveforms, we can get component of which the frequency is mainly between 500~800kHz. And the component varies according to the angle of the cross dipole appara tus.
Key words:cross dipole; sonic well logg ing; probe; acoustic
Jia Xiangdong , Liu Guoquan, Dong Bin, Chen Guangjian, Ling Bing, Bi Yuexin. Application of high resolu