冲压模具专业术语英汉对照
目录
一，
二，
三，
四，
五，
六，
七，
八，
九，
十， 模具厂常用之标准零配件 模具钢材 组装、冲压、喷漆等专业词汇 模具工程常用词汇 模具零件类 品质人员名称类 系统文件类 模具技术用语 各式模具分类用语 模具常用之工作机械设备
十一，表面处理关连用语
十二，成形不良用语
十三，各种冲模加工关连用语
十四，模具常用刀具与工作法用语
十五，冲压机械及周边关连用语
十六，线切割放电加工关连用语
十七，模具加工方法
十八，机械设计及周边其他用语
一，模具厂常用之标准零配件
air vent vale 通气阀 anchor pin 锚梢
angular pin 角梢 baffle 调节阻板
angular pin 倾斜梢 baffle plate 折流档板
ball button 球塞套 ball plunger 定位球塞
ball slider 球塞滑块 binder plate 压板
blank holder 防皱压板 blanking die 落料冲头
bolster 上下模板 bottom board 浇注底板
bolster 垫板 bottom plate 下固定板
bracket 托架 bumper block 缓冲块
buster 堵口 casting ladle 浇注包
casting lug 铸耳 cavity 模穴(模仁)
cavity retainer plate 模穴托板 center pin 中心梢
clamping block 锁定块 coil spring 螺旋弹簧
cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓
core 心型 core pin 心型梢
cotter 开口梢 cross 十字接头
cushion pin 缓冲梢 diaphragm gate 盘形浇口
die approach 模头料道 die bed 型底
die block 块形模体 die body 铸模座
die bush 合模衬套 die button 冲模母模
die clamper 夹模器 die fastener 模具固定用零件
die holder 母模固定板 die lip 模唇
die plate 冲模板 die set 冲压模座
direct gate 直接浇口 dog chuck 爪牙夹头
dowel 定位梢 dowel hole 导套孔
dowel pin 合模梢 dozzle 辅助浇口
dowel pin 定位梢 draft 拔模锥度
draw bead 张力调整杆 drive bearing 传动轴承
ejection pad 顶出衬垫 ejector 脱模器
ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套
ejector pad 顶出垫 ejector pin 顶出梢
ejector plate 顶出板 ejector rod 顶出杆
ejector sleeve 顶出衬套 ejector valve 顶出阀
eye bolt 环首螺栓 filling core 椿入蕊
film gate 薄膜形浇口 finger pin 指形梢
finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘?
flash gate 毛边形浇口 flask 上箱
floating punch 浮动冲头 gate 浇口
gate land 浇口面 gib 凹形拉紧?
goose neck 鹅颈管 guide bushing 引导衬套
guide pin 导梢 guide post 引导柱
guide plate 导板 guide rail 导轨
head punch 顶? 冲头 headless punch 直柄冲头
heavily tapered solid 整体模蕊盒 hose nippler 管接头
impact damper 缓冲器 injection ram 压射柱塞
inlay busher 嵌入衬套 inner plunger 内柱塞
inner punch 内冲头 insert 嵌件
insert pin 嵌件梢 king pin 转向梢
king pin bush 主梢衬套 knockout bar 脱模杵
land 合模平坦面 land area 合模面
leader busher 导梢衬套 lifting pin 起模顶?
lining 内衬 locating center punch 定位中心冲头
locating pilot pin 定位导梢 locating ring 定位环
lock block 压块 locking block 定位块
locking plate 定位板 loose bush 活动衬套
making die 打印冲子 manifold block 歧管档块
master plate 靠模样板 match plate 分型板
mold base 塑胶模座 mold clamp 铸模紧固夹
mold platen 模用板 moving bolster 换模保持装置
moving bolster plate 可动侧模板 one piece casting 整体铸件
parallel block 平行垫块 paring line 分模线
parting lock set 合模定位器 pass guide 穴型导板
peened head punch 镶入式冲头 pilot pin 导?
pin gate 针尖浇口 plate 衬板
pre extrusion punch 顶挤冲头 punch 冲头
puncher 推杆 pusher pin 衬套梢
rack 机架 rapping rod 起模杆
re-entrant mold 凹入模 retainer pin 嵌件梢
retainer plate 托料板 return pin 回位梢
riding stripper 浮动脱模器 ring gate 环型浇口
roller 滚筒 runner 流道
runner ejector set 流道顶出器 runner lock pin 流道拉梢
screw plug 头塞 set screw 固定螺丝
shedder 脱模装置 shim 分隔片
shoe 模座之上下模板 shoot 流道
shoulder bolt 肩部螺丝 skeleton 骨架
slag riser 冒渣口 slide(slide core) 滑块
slip joint 滑配接头 spacer block 间隔块
spacer ring 间隔环 spider 模蕊支架
spindle 主轴 sprue 注道
sprue bushing 注道衬套 sprue bushing guide 注道导套
sprue lock bushing 注道定位衬套 sprue puller 注道拉料?
spue line 合模线 square key 方键
square nut 方螺帽 square thread 方螺纹
stop collar 限位套 stop pin 止动梢
stop ring 止动环 stopper 定位停止梢
straight pin 圆柱? stripper bolt 脱料螺栓
stripper bushing 脱模衬套 stripper plate 剥料板
stroke end block 行程止梢 submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱 support pin 支撑梢
supporting plate 托板 sweep templete 造模刮板
tab gate 辅助浇口 taper key 推拔键
taper pin 拔锥梢/锥形梢 teeming 浇注
three start screw 三条螺纹 thrust pin 推力销
tie bar 拉杵 tunnel gate 隧道形浇口
vent 通气孔 wortle plate 拉丝模板
二，模具钢材
alloy tool steel 合金工具钢 aluminium alloy 铝合金钢
bearing alloy 轴承合金 blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢 clad sheet 被覆板 clod work die steel 冷锻模用钢
emery 金钢砂 ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢 martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁 merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢 nickel chromium steel 镍铬钢 prehardened steel 顶硬钢
silicon steel sheet 矽钢板 stainless steel 不锈钢
tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜
troostite 吐粒散铁 tungsten steel ?钢
vinyl tapped steel sheet 塑胶覆面钢板
三，组装、冲压、喷漆等专业词汇
Assembly line组装线
Layout 布置图
Conveyer 流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子
Pneumatic screw driver气动起子
worktable 工作桌
OOBA 开箱检查
fit together组装在一起
fasten 锁紧(螺丝)
fixture 夹具(治具)
pallet 栈板
barcode 条码
barcode scanner条码扫描器
fuse together熔合
fuse machine热熔机
repair 修理
operator 作业员
QC 品管
supervisor 课长
ME 制造工程师
MT 制造生技
cosmetic inspect外观检查
inner parts inspect内部检查
thumb screw大头螺丝
lbs. inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS
电源电压接拉键
sheet metal parts 冲件
plastic parts塑胶件
SOP 制造作业程序
material check list物料检查表
work cell工作间
trolley 台车
carton 纸箱
sub-line 支线
left fork叉车
production department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot 机械手
hydraulic machine油压机
lathe 车床
planer |'plein?|刨床
miller 铣床
grinder 磨床
driller 铣床
linear cutting线切割
electrical sparkle电火花
welder 电焊机
staker=reviting machine铆合机
position 职务
president 董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager | =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长 group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana 天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skr?pid|报废
scrape ..v.刮; 削
deficient purchase来料不良
manufacture procedure制程
deficient manufacturing procedure制程不良
oxidation |' ksi'dei?n|氧化
scratch 刮伤
dents 压痕
defective upsiding down抽芽不良
defective to staking铆合不良
embedded lump镶块
feeding is not in place送料不到位
stamping-missing 漏冲
production capacity生产力
education and training教育与训练
proposal improvement提案改善
spare parts=buffer备件
forklift 叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt 螺栓
name of a department部门名称
administration/general affairs dept总务部
automatic screwdriver电动启子
thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle 蜂鸣器
defective product label不良标签
identifying sheet list标示单
screwdriver holder起子插座
pedal 踩踏板
stopper 阻挡器
flow board流水板
hydraulic handjack油压板车
forklift 叉车
pallet 栈板
glove(s)手套
glove(s) with exposed fingers割手套
thumb 大拇指
forefinger 食指
midfinger 中指
ring finger无名指
little finger小指
band-aid 创可贴
iudustrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头
sweeper 扫把
mop 拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain 链条
jack 升降机
production line流水线
chain 链条槽
magnetizer 加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging 打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头
slipped screwhead/shippery screw thread滑手
speckle 斑点
mildewed=moldy=mouldy发霉
rust 生锈
deformation 变形
burr(金属)flash(塑件) 毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion 杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch 划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration 羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety 安全
quality 品质
delivery deadline交货期
cost 成本
engineering 工程
die repair模修
enterprise plan = enterprise expansion projects企划 QC 品管
die worker模工
production, to produce生产
equipment 设备
to start a press开机
stop/switch off a press关机
classification 整理
regulation 整顿
cleanness 清扫
conservation 清洁
culture 教养
qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品 waste 废料
board 看板
feeder 送料机
sliding rack滑料架
defective product box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket 蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料 to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation 运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
feature change 特性变更
evaluation 评估
prepare for, make preparations for 准备
parameters 参数
rotating speed, revolution转速
manufacture management制造管理
abnormal handling异常处理
production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
manufacture procedure制程
operation procedure作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over切换 engineering, project difficulty
工程瓶颈
stage die工程模
automation 自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模
shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder 送料机
rack, shelf, stack料架
cylinder 油缸
robot 机械手
taker 取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch 寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
reset 复位
smoothly 顺利
dent 压痕
scratch 刮伤
deformation 变形
filings 铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive 领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to send delinery back
to retrn of goods退货
registration 登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion 磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics 统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
四，模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt 螺栓
document folder文件夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment 设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量 quantity of customs count
会计师盘, 点数量
the first page第一联
filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO.
空白与作废单号
plate 电镀
mold 成型
material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点
sample 样品
incoming material to be inspected进货待验
description 品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location 地点
chairman 主席
present members出席人员
subject 主题
conclusion 结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet
PCE 组装厂生产排配表
model 机锺
work order工令
revision 版次
remark 备注
production control confirmation生产确认
checked by初审
approved by核准
department 部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total 合计
cause description原因说明
part number/ P/N 料号
type 形态
item/group/class类别
quality 品质
prepared by制表
notes 说明
year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials 物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单 spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM 放电机
coil stock卷料
sheet stock片料
tolerance 工差
score=groove压线
cam block滑块
pilot 导正筒
trim 剪外边
pierce 剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius 半径
shim(wedge)楔子
冲压模具专业术语英汉对照
目录
一，
二，
三，
四，
五，
六，
七，
八，
九，
十， 模具厂常用之标准零配件 模具钢材 组装、冲压、喷漆等专业词汇 模具工程常用词汇 模具零件类 品质人员名称类 系统文件类 模具技术用语 各式模具分类用语 模具常用之工作机械设备
十一，表面处理关连用语
十二，成形不良用语
十三，各种冲模加工关连用语
十四，模具常用刀具与工作法用语
十五，冲压机械及周边关连用语
十六，线切割放电加工关连用语
十七，模具加工方法
十八，机械设计及周边其他用语
一，模具厂常用之标准零配件
air vent vale 通气阀 anchor pin 锚梢
angular pin 角梢 baffle 调节阻板
angular pin 倾斜梢 baffle plate 折流档板
ball button 球塞套 ball plunger 定位球塞
ball slider 球塞滑块 binder plate 压板
blank holder 防皱压板 blanking die 落料冲头
bolster 上下模板 bottom board 浇注底板
bolster 垫板 bottom plate 下固定板
bracket 托架 bumper block 缓冲块
buster 堵口 casting ladle 浇注包
casting lug 铸耳 cavity 模穴(模仁)
cavity retainer plate 模穴托板 center pin 中心梢
clamping block 锁定块 coil spring 螺旋弹簧
cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓
core 心型 core pin 心型梢
cotter 开口梢 cross 十字接头
cushion pin 缓冲梢 diaphragm gate 盘形浇口
die approach 模头料道 die bed 型底
die block 块形模体 die body 铸模座
die bush 合模衬套 die button 冲模母模
die clamper 夹模器 die fastener 模具固定用零件
die holder 母模固定板 die lip 模唇
die plate 冲模板 die set 冲压模座
direct gate 直接浇口 dog chuck 爪牙夹头
dowel 定位梢 dowel hole 导套孔
dowel pin 合模梢 dozzle 辅助浇口
dowel pin 定位梢 draft 拔模锥度
draw bead 张力调整杆 drive bearing 传动轴承
ejection pad 顶出衬垫 ejector 脱模器
ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套
ejector pad 顶出垫 ejector pin 顶出梢
ejector plate 顶出板 ejector rod 顶出杆
ejector sleeve 顶出衬套 ejector valve 顶出阀
eye bolt 环首螺栓 filling core 椿入蕊
film gate 薄膜形浇口 finger pin 指形梢
finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘?
flash gate 毛边形浇口 flask 上箱
floating punch 浮动冲头 gate 浇口
gate land 浇口面 gib 凹形拉紧?
goose neck 鹅颈管 guide bushing 引导衬套
guide pin 导梢 guide post 引导柱
guide plate 导板 guide rail 导轨
head punch 顶? 冲头 headless punch 直柄冲头
heavily tapered solid 整体模蕊盒 hose nippler 管接头
impact damper 缓冲器 injection ram 压射柱塞
inlay busher 嵌入衬套 inner plunger 内柱塞
inner punch 内冲头 insert 嵌件
insert pin 嵌件梢 king pin 转向梢
king pin bush 主梢衬套 knockout bar 脱模杵
land 合模平坦面 land area 合模面
leader busher 导梢衬套 lifting pin 起模顶?
lining 内衬 locating center punch 定位中心冲头
locating pilot pin 定位导梢 locating ring 定位环
lock block 压块 locking block 定位块
locking plate 定位板 loose bush 活动衬套
making die 打印冲子 manifold block 歧管档块
master plate 靠模样板 match plate 分型板
mold base 塑胶模座 mold clamp 铸模紧固夹
mold platen 模用板 moving bolster 换模保持装置
moving bolster plate 可动侧模板 one piece casting 整体铸件
parallel block 平行垫块 paring line 分模线
parting lock set 合模定位器 pass guide 穴型导板
peened head punch 镶入式冲头 pilot pin 导?
pin gate 针尖浇口 plate 衬板
pre extrusion punch 顶挤冲头 punch 冲头
puncher 推杆 pusher pin 衬套梢
rack 机架 rapping rod 起模杆
re-entrant mold 凹入模 retainer pin 嵌件梢
retainer plate 托料板 return pin 回位梢
riding stripper 浮动脱模器 ring gate 环型浇口
roller 滚筒 runner 流道
runner ejector set 流道顶出器 runner lock pin 流道拉梢
screw plug 头塞 set screw 固定螺丝
shedder 脱模装置 shim 分隔片
shoe 模座之上下模板 shoot 流道
shoulder bolt 肩部螺丝 skeleton 骨架
slag riser 冒渣口 slide(slide core) 滑块
slip joint 滑配接头 spacer block 间隔块
spacer ring 间隔环 spider 模蕊支架
spindle 主轴 sprue 注道
sprue bushing 注道衬套 sprue bushing guide 注道导套
sprue lock bushing 注道定位衬套 sprue puller 注道拉料?
spue line 合模线 square key 方键
square nut 方螺帽 square thread 方螺纹
stop collar 限位套 stop pin 止动梢
stop ring 止动环 stopper 定位停止梢
straight pin 圆柱? stripper bolt 脱料螺栓
stripper bushing 脱模衬套 stripper plate 剥料板
stroke end block 行程止梢 submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱 support pin 支撑梢
supporting plate 托板 sweep templete 造模刮板
tab gate 辅助浇口 taper key 推拔键
taper pin 拔锥梢/锥形梢 teeming 浇注
three start screw 三条螺纹 thrust pin 推力销
tie bar 拉杵 tunnel gate 隧道形浇口
vent 通气孔 wortle plate 拉丝模板
二，模具钢材
alloy tool steel 合金工具钢 aluminium alloy 铝合金钢
bearing alloy 轴承合金 blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢 clad sheet 被覆板 clod work die steel 冷锻模用钢
emery 金钢砂 ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢 martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁 merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢 nickel chromium steel 镍铬钢 prehardened steel 顶硬钢
silicon steel sheet 矽钢板 stainless steel 不锈钢
tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜
troostite 吐粒散铁 tungsten steel ?钢
vinyl tapped steel sheet 塑胶覆面钢板
三，组装、冲压、喷漆等专业词汇
Assembly line组装线
Layout 布置图
Conveyer 流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子
Pneumatic screw driver气动起子
worktable 工作桌
OOBA 开箱检查
fit together组装在一起
fasten 锁紧(螺丝)
fixture 夹具(治具)
pallet 栈板
barcode 条码
barcode scanner条码扫描器
fuse together熔合
fuse machine热熔机
repair 修理
operator 作业员
QC 品管
supervisor 课长
ME 制造工程师
MT 制造生技
cosmetic inspect外观检查
inner parts inspect内部检查
thumb screw大头螺丝
lbs. inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS
电源电压接拉键
sheet metal parts 冲件
plastic parts塑胶件
SOP 制造作业程序
material check list物料检查表
work cell工作间
trolley 台车
carton 纸箱
sub-line 支线
left fork叉车
production department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot 机械手
hydraulic machine油压机
lathe 车床
planer |'plein?|刨床
miller 铣床
grinder 磨床
driller 铣床
linear cutting线切割
electrical sparkle电火花
welder 电焊机
staker=reviting machine铆合机
position 职务
president 董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager | =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长 group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana 天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skr?pid|报废
scrape ..v.刮; 削
deficient purchase来料不良
manufacture procedure制程
deficient manufacturing procedure制程不良
oxidation |' ksi'dei?n|氧化
scratch 刮伤
dents 压痕
defective upsiding down抽芽不良
defective to staking铆合不良
embedded lump镶块
feeding is not in place送料不到位
stamping-missing 漏冲
production capacity生产力
education and training教育与训练
proposal improvement提案改善
spare parts=buffer备件
forklift 叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt 螺栓
name of a department部门名称
administration/general affairs dept总务部
automatic screwdriver电动启子
thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle 蜂鸣器
defective product label不良标签
identifying sheet list标示单
screwdriver holder起子插座
pedal 踩踏板
stopper 阻挡器
flow board流水板
hydraulic handjack油压板车
forklift 叉车
pallet 栈板
glove(s)手套
glove(s) with exposed fingers割手套
thumb 大拇指
forefinger 食指
midfinger 中指
ring finger无名指
little finger小指
band-aid 创可贴
iudustrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头
sweeper 扫把
mop 拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain 链条
jack 升降机
production line流水线
chain 链条槽
magnetizer 加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging 打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头
slipped screwhead/shippery screw thread滑手
speckle 斑点
mildewed=moldy=mouldy发霉
rust 生锈
deformation 变形
burr(金属)flash(塑件) 毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion 杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch 划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration 羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety 安全
quality 品质
delivery deadline交货期
cost 成本
engineering 工程
die repair模修
enterprise plan = enterprise expansion projects企划 QC 品管
die worker模工
production, to produce生产
equipment 设备
to start a press开机
stop/switch off a press关机
classification 整理
regulation 整顿
cleanness 清扫
conservation 清洁
culture 教养
qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品 waste 废料
board 看板
feeder 送料机
sliding rack滑料架
defective product box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket 蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料 to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation 运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
feature change 特性变更
evaluation 评估
prepare for, make preparations for 准备
parameters 参数
rotating speed, revolution转速
manufacture management制造管理
abnormal handling异常处理
production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
manufacture procedure制程
operation procedure作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over切换 engineering, project difficulty
工程瓶颈
stage die工程模
automation 自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模
shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder 送料机
rack, shelf, stack料架
cylinder 油缸
robot 机械手
taker 取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch 寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
reset 复位
smoothly 顺利
dent 压痕
scratch 刮伤
deformation 变形
filings 铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive 领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to send delinery back
to retrn of goods退货
registration 登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion 磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics 统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
四，模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt 螺栓
document folder文件夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment 设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量 quantity of customs count
会计师盘, 点数量
the first page第一联
filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO.
空白与作废单号
plate 电镀
mold 成型
material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点
sample 样品
incoming material to be inspected进货待验
description 品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location 地点
chairman 主席
present members出席人员
subject 主题
conclusion 结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet
PCE 组装厂生产排配表
model 机锺
work order工令
revision 版次
remark 备注
production control confirmation生产确认
checked by初审
approved by核准
department 部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total 合计
cause description原因说明
part number/ P/N 料号
type 形态
item/group/class类别
quality 品质
prepared by制表
notes 说明
year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials 物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单 spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM 放电机
coil stock卷料
sheet stock片料
tolerance 工差
score=groove压线
cam block滑块
pilot 导正筒
trim 剪外边
pierce 剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius 半径
shim(wedge)楔子