★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
1 / 16
版本Version ：页 码Page ：
文件发行File Release/修订履历Revised resume
Copyright BYD Company Limited
版本Version 日 期 Date
ECN 编号 ECN number
修 改 内 容 Revised resume
修改/创建人 Update/Creator
张会
首次发行
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
章节号 Chapter No.
1 2 3 4 5 6 7 8
项目编号（可选）Item number
2 / 16
版本Version ：页 码Page ：
内 容 Content 目的 Purpose 适用范围 Scope 参考文件 References 定义 Definition 职责 Duties
检验条件 Inspection conditions 检验标准 Inspection standard
包装Package
页 次 Page 2 2 3 3 3 3 4--16 16
1
目的 Purpose
明确BYD 太阳能组件的出货标准，确保客户满意。
Release BYD standard for general solar modules, ensure customer satisfaction.
2 适用范围 Scope
适用于第二事业部PVS 上海产品部P6-18、P6-24、P6-30、P6-36等标准品型号组件出货检验。
For all P6-18、P6-24、P6-30、P6-36 PV modules made by the Shanghai Products Group, 2 division, BYD.
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
3 / 16
版本Version ：页 码Page ：
3 参考文件 3.1
地面用晶体硅光伏组件—设计鉴定和定型 IEC 61215-2005
Crystalline silicon aground photovoltaic modules - Design qualification and type approval IEC 61215-2005 3.2
各工序工艺标准、原材料标准
Standards of the various technological processes, raw materials standards 3.3
各客户标准
The Client Standard original file.
4 定义Definition 无 No
5 职责 Duties
5.1 PVS上海产品部品质科负责制定、维护本检验标准；
Quality group of PVS Production dept. responsible for developing, maintaining the standard. 5.2
品质科OQC 根据本文件规定，在出货前选用、填写相应的《出货检验报告》。
The quality OQC the provisions of this document, Prepare Inspect report before shipping.
6
检验条件 Inspect Conditions 6.1 6.2
组件的外观检验照度≥1000Lx ，距离30-50CM ，裸眼视力在1.2以上。
对于色差组件的检验, 距离2米，裸眼视力在1.2以上对垂直放置在桌面上的组件进行观察，若看不到明显色差则判定A 级组件。
Inspect the appearance of the solar panel under the 1000 lx illuminance, distance between 0.3 and 0.5 meter, the naked eyesight above 1.2, Inspect the chromatic aberration of the solar panel under 1000 lx illuminance, distance 2 meters, naked eyesight above 1.2, to inspect the solar panel on the table with eyes, classify the solar panel to Grade A if there's no apparent chromatic aberration. 6.3
对于铝型材和钢化玻璃划伤的检验, 距离1米，裸眼视力在1.2以上对材料进行观察，若看不见的则判定为A 级组件。
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
4 / 16
版本Version ：页 码Page ：
Inspect the scratch on the aluminum frame and tempered glass: Under 1000 lx illuminance, distance 1 meter, naked eyesight above 1.2, to inspect the material, if can not see any scratch, it is grade A； 7
B 级（外观低于A 级）
编号No
位置 Position
缺陷 Defect
检查工具 Inspect tools 目视+卡尺 Unaided eyes & callipers 目视+卡尺Unaided eyes & callipers
标准描述 Standard Description 不允许存在
宽度小于0.2mm ，长度小于10mm 的划伤，每平方米面积内不多于1条；深度要求用指甲盖滑过没有明显的阻力感。The width smaller than 0.2mm，length smaller than 50mm，quantity of such scratch smaller than 4 /m²
a) 电池片上，气泡面积不大于4mm²，每平方米面积内数量不多于2个，并且不在同一个电池片上；
目视+卡尺&callipers
a) on the solar cell, the air bubble area must not bigger 2 in every one square meter and can not be located in same solar cell.
b) 不在电池片上，气泡面积不大于8mm²，每平方米面积内
Copyright BYD Company Limited
检验标准 Standards
A 级（优质） A Grade(Excellent) B Grade(Appearance grade lower than grade A)
标准描述 Standard Description 面积1~10mm²数量≤3个。 Area1~10mm²，Quantity ≤3个.
划伤宽度0.2-0.5mm ，长度小于30mm ，每平方米面积内不多于3条。
The width between 0.2mm and 0.5mm，length smaller than 30mm，quantity of such scratch no more than 3/㎡
a) 电池片上，气泡面积小于4mm²，每平方米面积内不多于2个，并且不在同一个电池片上；
must smaller than 4mm²，quantity of such air bubble must no more than 2PCS/m²and can not be located in same solar cell；
1.1
钢化玻璃Glass
脏污 Dirty
1.2
钢化玻璃Glass
划伤 Scratch
组件内气泡及玻璃
1.3
钢化玻璃Glass
内气泡 Air bubble inside the solar panel or
Unaided eyes than 4mm²，quantity of such air bubble must not more than a) on the solar cell, the air bubble area
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066 the tempered glass
项目编号（可选）Item number
5 / 16
版本Version ：页 码Page ：数量不多于3；
than 8mm²，the quantity of such air bubble must no more than three in every one square meter. c) 距离玻璃边5mm 宽度之内不允许出现气泡
c) bubbles present within 5 mm of edge of glass is limited .d) 长度或直径小于1mm 的气泡小于10个/m²。 d) bubbles which’s length or diameter is bigger than 1mm,allow 10PCS/m²
b) 不在电池片上，气泡面积小于25mm²，b)Not on the solar cell, the air bubble area must not smaller than 25mm²，the quantity of such air bubble must no more than five in every one square meter；
c) 距离玻璃边5mm 宽度之内不允许出现气泡
c) bubbles present within 5 mm of edge of glass is limited .
d) 长度或直径小于1mm 的气泡允许10~15个/m²。
d) bubbles which’s length is bigger than 1mm,allow 10PCS/m²
a) 污垢不得引起内部短路，面积小于1cm²，每平方米内1~3个；
a)The dirty must not cause the internal short-circuit, the area must be less than 1cm²，the quantity of such dirty area must be no more than 5 in every one square meter. ；
b ）长度在10mm 内的毛发或毛发状异物允许数量2条以下，且出现的位置不允许可能导致短路或形成气泡通道。
b)Not on the solar cell, the air bubble area must not bigger 在1m²内不超过5个；
a ）组件内部允许存在长度或直径小于3mm 的异物，但是异物不得引起内部短路，每平方米面积内数量不多于1个。a ）The inside dirty length or diameter must be smaller than
1.4
钢化玻璃Glass
内部污垢Inside dirty
目视+卡尺&callipers
3 mm，and the dirty area can not cause the internal more than three in every one square meter.
b ）不允许毛发或金属类导电异物在电池片或汇流条处，以至于造成电池片短路。不允许在组件边缘出现毛发或毛发状异物以至于有形成气泡通道的危险。
Unaided eyes short-circuit, the quantity of such dirty area must be no
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
6 / 16
版本Version ：页 码Page ：
b ）Length within 10mm hair or hair-like foreign materials inside. Mustn’t result in internal short-circuit.
铝外框接缝处 The 2.1 juncture
of the aluminu m frames铝外框侧面 2.2 side of
aluminu m frame 铝外框背面 2.3 bottom of aluminu m frame 铝外框正2.4
面 Surface of
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：0个 area ≤4mm²，0pcs each module.
面积≤4mm²，每根边框数量≤2处 area ≤4mm²，quantity in each frame≤2
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤8mm²，每块组件允许的数量：≤3个 area ≤8mm²，quantity in each frame≤3.
面积≤8mm²，每根边框允许的数量≤2个 area ≤8mm²，quantity in each frame≤3
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：0个 area ≤4mm²，quantity in each frame 0 .
面积≤4mm²、每根边框数量≤2个 area ≤4mm²、quantity in each frame≤2
脏污Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：≤1个 Dirty Area≤4mm²，Dirty area quantity 0.
面积≤4mm²，数量≤2个
dirty area≤4mm², Dirty Area Quantity≤2
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
7 / 16
版本Version ：页 码Page ：
aluminu m frame
a) 铝型材接缝配合良好，缝隙不超过0.35mm ； a) The clearance between the aluminum frames must be no more than 0.35mm.
b) 表面清洁干净，不得有字迹； handwriting.
c) 所有型材断缝处、安装口处不得有毛刺；
目视+卡尺+
铝外框组2.5
框 Aluminu m Frame
塞尺
划伤、间隙Scratch,cl earance
Unaided eyes ,calipers &feeling guage
c) The cross section or the installation hole of the aluminum frame must have no burr. d) 铝边框允许有不明显的轻微划伤； 正面划伤不允许有划破表面氧化膜；
侧面、背面划伤，宽度小于0.2mm ，长度小于10mm ； d) The slightly scratch which is not so obvious is allowed; the scratch on the top must not lacerate the oxidated film on the surface, the lacerated area at the rear and flank of the solar panel, width must be less than 0.2mm, length must be smaller than 10mm.
e) 组件长短边框安装上下错位≤0.5mm
e) The malposition (in upright direction) results from the installation of the long and short aluminum frame must be ≤0.5mm.
f) 模组边平行度没有在3mm 之内，模组的方形[（对角
Copyright BYD Company Limited
a) 铝型材接缝配合缝隙0.35mm-0.5mm ； a)The clearance between the aluminum frames 0.35mm-0.5mm； b) 表面清洁干净，不得有字迹； handwriting ；
c) 所有型材断缝处、安装口处不得有有可能引起人员伤害的毛刺；
c) The burr at the cross section and the installation hole can not hurt persons； d) 划伤有轻微刺破氧化膜；
划伤宽度0.2-0.5mm ，长度10-50mm ； 非线状擦伤，面积4mm²-100mm²，轻微刺破氧化膜。
d) lacerate the oxidated film slightly； the lacerating area, width 0.2-0.5mm，length between 10-50mm； none-linear scratch ,area between 4mm²-100mm²，slightly puncture the oxidated film。
e) 组件边框安装上下错位，不超过1mm ； e)The malposition(in upright direction)
b) The surface of the aluminum must be clean and has no b) The surface must be clean and no
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
8 / 16
版本Version ：页 码Page ：线1-对角线2）]/2大于1.5mm. 测量对 角线或者拐角的距离
modules [(Diagonal 1 – Diagonal 2))/2 is greater than 1.5 mm. Done by measuring Diagonal or distance between corners.
g) 流水孔错位
g) The malposition of the scupper
results from the installation of the aluminum frame must be no more than f) 模组边平行度没有在3mm 之内，模组的方形（对角线[1-对角线2）]/2大于1.5mm. 测量对
角线或者拐角的距离
f) Module sides are not parallel within 3 mm Squareness of modules [(Diagonal 1 – Diagonal 2))/2 is greater than 1.5 mm. Done by measuring Diagonal or distance between corners. g) 流水孔错位
g) The malposition of the scupper
f) Module sides are not parallel within 3 mm Squareness of 1mm ；
a) 组件正面边框与玻璃之间的隙宽度和深度测量，用厚度小于0.3mm 塞规检测。铝边框四角垂直方向塞规深入距离
封胶 3.1
Glue Sealing
封胶不可见 The glue must be invisible
目视+塞尺Unaided eyes & plug guage
a)Use the 0.3mm plug guage to measure the clearance between the top aluminum frame and the glass。At the direction of 45° to the 1mm depth slot aluminum frame, at the corner the plug guage can insert
b) 背板与边框不允许出现间隙
Copyright BYD Company Limited
a) 组件正面边框与玻璃之的间隙宽度和深度测量，用厚度小于0.3mm 塞规检测。铝边框四角垂直方向塞规深入距离
a)Use the 0.3mm plug guage to measure the clearance between the top aluminum frame and the glass。At the direction of 45° to the 1mm depth slot aluminum frame, at the corner the plug guage can
insert
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
9 / 16
版本Version ：页 码Page ：b)Sealant must excess out from the frame, no gap in bed of sealant.
the plug guage can insert
b)Sealant must excess out from the frame, no gap in bed of sealant.
接线盒 4.1 Junction
box
接线盒脏污 Dirty
目视 Unaided eyes
不允许接线盒上有硅胶
No silicon gel on the junction box. a) 硅胶溢出接线盒边缘3-7mm ；
a) The excess sealant width is within3-7mm, at the edge of the J-box
b) 盒内汇流条引出线TPT 开口完全被硅胶密封； b) The TPT clearance where the conflux belt go out must be completely sealed by the silicon gel. c) 二极管极性一致，数量方向正确；
c) The polarity of the diodes must be consistent, the quantity and the direction must correct. d ）汇流条表面干净、固定牢固
d ）The surface of the conflux belt is clean and be fixed stably.
不允许接线盒上有硅胶
No silicon gel on the junction box a) 硅胶溢出接线盒边缘3-7mm ； a) The excess sealant width is within3-7mm, at the edge of the J-box b) 不允许汇流条开口长度大于接线盒宽度； b) The cut width of the backsheet longer than width of the junction box, can’t accept. c) 二极管极性一致，数量方向正确； c) The polarity of the diodes must be consistent, the quantity and the direction must correct；
d ）汇流条表面干净、固定牢固。
d ）The surface of the conflux belt is clean and be fixed stably
a ）引出线需要有正负极标识；
a ）The cable must be marked with polarity b ）不允许公母头有损坏或正、负级接反现象；
接线盒外观
接线盒 4.2 Junction
Box
The appearan ce of the junction box
目视+卡尺Unaided eyes &callipers
接线盒 4.3 Junction
Box
引出电缆Cable
目视+卡尺Unaided eyes &callipers
a ）引出线需要有正负极标识；
a ）The cable must be marked with polarity. b ）不允许公母头有损坏或正、负级接反现象；
b ）The male/female connector must not be damaged or
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
10 / 16
版本Version ：页 码Page ：connected with wrong polarity.
c ）引出线和公母头上不允许有硅胶或脏污。 and have no silicon gel.
d ）公母头与标准公母头搭配组装，不能出现有松动或过紧的状况。
d ）The male/female connector must be installed with standard male/female connector, must not be too tight or loose.
b ）The male/female connector must not be damaged or connected with wrong polarity c ）The cable and the male/female connector must be clean and have no silicon gel
d ）公母头与标准公母头搭配组装，不能出现有松动或过紧的状况。
d ）The male/female connector must be installed with standard male/female connector, must not be too tight or loose a) 处于层压组件边缘的褶皱或折痕；介于电池片边缘和玻璃边缘之间的褶皱或折痕；处于接线盒与背板连接处的褶皱或折痕不允许存在
a)Wrinkles or folds at edge of laminate or between edge of cell and edge of glass or at junction box
b) 超过1mm 宽度的褶皱或折痕不允许存在 b)Wrinkles or folds greater than 1 mm in width
c) 覆盖范围超过组件面积的10%的褶皱或折痕不允许存在
c)Wrinkles cover greater than 10 % of
c ）The cable and the male/female connector must be clean c ）引出线和公母头上不允许有硅胶或脏污
a) 处于层压组件边缘的褶皱或折痕；介于电池片边缘和玻璃边缘之间的褶皱或折痕；处于接线盒与背板连接处的褶皱或折痕不允许存在
TPT 表面5.1 TPT
surface
Wrinkles/Folds 褶皱或折痕
目视+卡尺Unaided eyes &callipers
a)Wrinkles or folds at edge of laminate or between edge of cell and edge of glass or at junction box b) 超过1mm 宽度的褶皱或折痕不允许存在 b)Wrinkles or folds greater than 1 mm in width
c) 覆盖范围超过组件面积的10%的褶皱或折痕不允许存在 c)Wrinkles cover greater than 10 % of backsheet area d) 允许由于焊带引起的规则褶皱
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
11 / 16
版本Version ：页 码Page ：
backsheet area
背面有鼓包，单个面积不大于100mm²，高
鼓包面积不大于50mm²，鼓包高度不超过1mm ，每平方米面积内不超过1个，鼓包不得出现自组件边缘10mm 宽度
TPT 表面5.2 TPT
surface
鼓包Heave
目视+卡尺&callipers
的地方。
height must be no more than 1mm, the quantity of the the heave must not touch the edge of the solar panel. a) 异物引起的几种凹痕，包括处于层压组件边缘的凹痕；介于电池片边缘和玻璃边缘之间的凹痕；处于接线盒与背板连接处的凹痕。以上凹痕不允许存在
a)Indentations on backsheet from contact with object of foreign source (excluding components of processing
TPT 表面5.3 TPT
surface
凹陷Depresse d area
目视+卡尺&callipers
equipment) or improper equipment maintenance at edge junction box. Indentations mentioned can’t accept b) 层压过称中由异物或不恰当的设备引起的小于50mm 长度的凹痕≤3条
b)Indentations on backsheet from contact with object of foreign source (excluding components of processing equipment) or improper equipment maintenance less than
Copyright BYD Company Limited
度不超过2mm ，每平方米面积内个数不超过3个，鼓包不得出现在组件边缘10mm 宽度的地方。
the area of single heave must be no more than 2mm，the quantity must be no more than 3 in every one square meter。
Unaided eyes The heave area must be no bigger than 50mm²，the heave The heave at the rear of the solar panel,
heave must be no more than 2 in every one square meter, than100mm²，the height must be no more
凹陷面积100mm²-300mm²，深度2-3mm ，每平方米面积内数量不超过15个 depth 2-3mm，the quantity must be no more than 15 per square meter
Unaided eyes of laminate or between edge of cell and edge of glass or at The depressed area 100mm²-300mm²，
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
12 / 16
版本Version ：页 码Page ：50 mm in length
c) 层压过称中由异物或不恰当的设备引起的大于50mm 长度的凹痕不允许存在。
c)Indentations on backsheet from contact with object of foreign source (excluding components of processing equipment) or improper equipment maintenance less than 50 mm in length
允许表面擦痕，划伤无明显深度，不得划破表面T 层, 宽度小于0.1mm ，长度小于20mm ，每平方米面积内不多于1条。
Scrape on the surface is allowed to pass, the lacerating area has no obvious depth and must not damage the TPT, the width must be smaller than 0.1mm,the length must be smaller than 20mm, the quantity must be no more than1pcs per quare meter.
组件电池颜色均匀一致，颜色范围深蓝色、蓝色到淡蓝色，允许相近颜色存在，但不允许电池片跳色，如：从黑色到蓝
a. 划伤宽度0.1-0.5mm ，划伤长度不大于
50mm ；
a. The width of the lacerating area
between0.1-0.5mm ，length must be no bigger than 20mm； b. 划破TPT ，长度小于20mm. b. The TPT is lacerated with the length smaller than 20mm.
同一组件上电池片跳色色斑，同一电池片上有跳色色差。
The color change suddenly in one solar panel, the color change suddenly in one solar cell。
TPT 表面5.4 TPT
surface
划伤scratch
目视+卡尺Unaided eyes &callipers
电池片 6.1 Solar
cells
色差chromatis m
目视Unaided
eyes
色。
The color of the solar panel must be average and consistent, the color ranges from dark blue, blue to light blue, the color is a little different in different area is OK, if the color suddenly changes(from black to blue for
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
13 / 16
版本Version ：页 码Page ：example) is not allowed to pass the inspection.
a) 不允许有三角形缺口和尖锐形缺口。 a) Triangle indentation and sharp
a) 不允许有V 形缺口，对于非V 缺口的要求如下： a) V shape indentation is not allowed.
b) 组件电池片边缘崩边，长度≤2mm ，深度≤0.5mm(多晶≤1.0mm) ，每块组件数量≤2处；
depth ≤0.5mm(polycrystalline≤1.0mm) ，quantity ≤2. c) 四角缺口：尺寸≤1.5 mm×1.5mm，数量≤1处；
目视+卡尺&callipers
c)Four angles indentation：demension ≤1.5 mm×1.5mm，以上缺口崩边均不可过电极(主栅线、副栅线) ，每平方面积内数量少于2个；
All the chipping and indentation can not be touch the bar line(main bar line and smaller bar line), such defect quantity must be less than 2 in every one square meter. 主栅线±5mm内不允许出现缺口、崩边。 main bar line.
Unaided eyes quantity ≤1.
indentation is not allowed。
b) 电池边缘崩边和缺口，其长度≤5mm ，深度不超过边缘栅线，数量≤3处；
四角缺口：尺寸≤2mm×2mm，数量≤1处； 每个组件缺口崩边数量≤5个。 b) the chipping and the indentation at the edge of the solar cell,length≤5mm ，depth can not be over the bar line on the edge, quantity ≤3；
four angles indentation ：
dimension ≤2mm×2mm，quantity ≤1； stringy indentation ：length ≤15mm ，quantity ≤1；
The quantity of the chipping and c) 允许崩边、缺口、掉角电池片碎渣留在组件内，但不允许因此而使两片电池片、电池片到汇流条、电池片到边框形成连通。（两
Copyright BYD Company Limited
b)The chipping on the edge of the solar cell: length≤2mm ， 细长形缺口：长度≤15mm ，数量≤1处；
崩边、缺
电池片 6.2 Solar
cells
口、破角chipping, indentatio n, corner breaking
no chipping and indentation is allowed inside ±5mm of the indentation for each panel≤5。
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
14 / 16
版本Version ：页 码Page ：
片电池片之间的碎渣最多只能与一边电池或互联条连通，与另一边电池距离必须大于0.2mm
c)The broken bits result from chipping, indentation and corner breaking can be in the solar panel, but can not conduct the solar cell, conflux belt with other solar cell, aluminum frame or conflux belt (the broken bits between two solar cells can touch one of the cells but must be away from another cell for more than 0.2mm)
栅线清晰，断栅长度≤2mm ，同一电池片上断栅累计长度不
电池片 6.3 Solar
cells
电池栅线Solar cell bar line
目视+卡尺&callipers
超过10mm ，不能允许有相邻的断栅存在
break off bar lines must be no more than 10mm,different bar lines must not be neighbouring from each other. a) 电池片的排列基本均匀，片间距为1.6mm ～3.5mm.
电池片排
电池片 6.4 Solar
cells
列 Solar cell collocatio n
目视+卡尺&callipers
串间距2mm ～4mm 。
Unaided eyes between solar cells and the distance between solar cell
strings range in 1.6mm～3.5mm.
And the distance between solar cell strings range in 2mm ～4mm.
Copyright BYD Company Limited
同一电池片上断栅累计长度20-30mm ； 允许有相邻断栅。
The bar line length≤2mm ，the total length of the break off bar lines must be 20mm-30mm,different bar lines can be neighbouring from each other. a ）片间距、串间距1.6-4.0mm
a) the distance between solar cells and the 1.6mm ～4mm.
And the distance between solar cell strings range in 1.6mm～4mm.
b ）边框内侧到电池片的间距＞3mm 。
Unaided eyes The bar line is clear,length≤2mm ，the total length of the
a)The collocation of the solar cells is average, the distance distance between solar cell strings range in
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
15 / 16
版本Version ：页 码Page ：b ）边框内侧到电池片的间距9±2mm 。
b ）The distance from aluminum to solar cell9±2mm. c ）边框内侧到汇流条的间距≥6mm 。
c ）The distance from aluminum to conflux belt≥6mm d) 焊带露白宽度≤0.3mm ，每片电池片上主栅线露白长度不d) The naked area of the siliver pole≤0.3mm. length not longer than 150mm
b ）The distance from aluminum to solar cell＞3mm.
c ）边框内侧到汇流条的间距＞3mm 。 c ）The distance from aluminum to conflux belt ＞3mm
d) The naked area of the siliver pole ≤0.5mm 。
电池片存在可视裂纹, 裂纹长度小于电池片长度的1/3，裂纹和它的延长线造成失效面积≤10%，组件IV 曲线无异常
The visible crack on the cell, its length is less than 1/3 of the length of the solar cell, the invalid area on the solar cell results from crack and its extended line must be smaller than≤10%，the IV curve of the solar panel has no abnormal
超过50mm ，每块组件电池片主栅线露白总长度≤150mm 。d ）焊带露白≤0.5mm ；
电池片裂
电池片 6.5 Solar
cells
纹、隐裂Solar cell crack and invisible crack
目视 Unaided eyes
电池片不存在任何裂纹
No crack( visible or invisible) on the solar cell.
IV 曲线异
7.1
IV 测试 IV Test
常 IV Curve Abnormal
8.1
标签 Label
铭牌Nameplat e
测试仪+目视
tester &Unaided eyes 目视+卡尺Unaided eyes & callipers
按照图纸要求
Refer to the standard drawing.
I-V 曲线平滑没有台阶
I-V curve is smooth and has no step.
I-V 曲线有台阶 I-V curve has step
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
16 / 16
版本Version ：页 码Page ：
a) 边框条码与组件玻璃内条码一致；
a) 边框条码与组件玻璃内条码一致；
8.2
标签 Label
条形码 Bar code
目视 Unaided eyes
a) The bar code of the aluminum frame must be consistent with the bar code under the glass.
b ）清晰可以识别，粘贴端正、无褶皱、无翘起。 b ）Clear and easy to recognize, no tilt and deflection.
a) The bar code of the aluminum frame must be consistent with the bar code under the glass；
b ）清晰可以识别，粘贴端正、无褶皱、无翘起。
b ）Clear and easy to recognize, no tilt and deflection.
8.3
标签 Label 功率要求8.4
Power requirem ent 8.5
物料 Materials 物料 Materials
接地标识Grounding mark 电性能参数 I-V data 物料 Materials 连接器Connector
目视 Unaided eyes
接地标识位置正确
The grounding mark must be in the correct position.
接地标识位置正确
The grounding mark must be in the correct position.
太阳能模拟器Simulator 依照BOM Check by BOM 连接器型号 The type of the connector
出货要求：按照各项目太阳能电池组件客户需求信息表要求，平均功率正偏差。 Shipment requirement: According to the table of every client, average positive deviation.
原材料与工艺工程师提供的BOM 清单一致。
Materials according to BOM which approved by technologist. 参考各项目太阳能电池组件客户需求信息表。 According to the table of every client.
8.6
8. 包装根据BYD 标准品或客户指定包装要求进行包装。
Package should accord to BYD standardized mode of product package or customers’ requirements
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
1 / 16
版本Version ：页 码Page ：
文件发行File Release/修订履历Revised resume
Copyright BYD Company Limited
版本Version 日 期 Date
ECN 编号 ECN number
修 改 内 容 Revised resume
修改/创建人 Update/Creator
张会
首次发行
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
章节号 Chapter No.
1 2 3 4 5 6 7 8
项目编号（可选）Item number
2 / 16
版本Version ：页 码Page ：
内 容 Content 目的 Purpose 适用范围 Scope 参考文件 References 定义 Definition 职责 Duties
检验条件 Inspection conditions 检验标准 Inspection standard
包装Package
页 次 Page 2 2 3 3 3 3 4--16 16
1
目的 Purpose
明确BYD 太阳能组件的出货标准，确保客户满意。
Release BYD standard for general solar modules, ensure customer satisfaction.
2 适用范围 Scope
适用于第二事业部PVS 上海产品部P6-18、P6-24、P6-30、P6-36等标准品型号组件出货检验。
For all P6-18、P6-24、P6-30、P6-36 PV modules made by the Shanghai Products Group, 2 division, BYD.
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
3 / 16
版本Version ：页 码Page ：
3 参考文件 3.1
地面用晶体硅光伏组件—设计鉴定和定型 IEC 61215-2005
Crystalline silicon aground photovoltaic modules - Design qualification and type approval IEC 61215-2005 3.2
各工序工艺标准、原材料标准
Standards of the various technological processes, raw materials standards 3.3
各客户标准
The Client Standard original file.
4 定义Definition 无 No
5 职责 Duties
5.1 PVS上海产品部品质科负责制定、维护本检验标准；
Quality group of PVS Production dept. responsible for developing, maintaining the standard. 5.2
品质科OQC 根据本文件规定，在出货前选用、填写相应的《出货检验报告》。
The quality OQC the provisions of this document, Prepare Inspect report before shipping.
6
检验条件 Inspect Conditions 6.1 6.2
组件的外观检验照度≥1000Lx ，距离30-50CM ，裸眼视力在1.2以上。
对于色差组件的检验, 距离2米，裸眼视力在1.2以上对垂直放置在桌面上的组件进行观察，若看不到明显色差则判定A 级组件。
Inspect the appearance of the solar panel under the 1000 lx illuminance, distance between 0.3 and 0.5 meter, the naked eyesight above 1.2, Inspect the chromatic aberration of the solar panel under 1000 lx illuminance, distance 2 meters, naked eyesight above 1.2, to inspect the solar panel on the table with eyes, classify the solar panel to Grade A if there's no apparent chromatic aberration. 6.3
对于铝型材和钢化玻璃划伤的检验, 距离1米，裸眼视力在1.2以上对材料进行观察，若看不见的则判定为A 级组件。
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
4 / 16
版本Version ：页 码Page ：
Inspect the scratch on the aluminum frame and tempered glass: Under 1000 lx illuminance, distance 1 meter, naked eyesight above 1.2, to inspect the material, if can not see any scratch, it is grade A； 7
B 级（外观低于A 级）
编号No
位置 Position
缺陷 Defect
检查工具 Inspect tools 目视+卡尺 Unaided eyes & callipers 目视+卡尺Unaided eyes & callipers
标准描述 Standard Description 不允许存在
宽度小于0.2mm ，长度小于10mm 的划伤，每平方米面积内不多于1条；深度要求用指甲盖滑过没有明显的阻力感。The width smaller than 0.2mm，length smaller than 50mm，quantity of such scratch smaller than 4 /m²
a) 电池片上，气泡面积不大于4mm²，每平方米面积内数量不多于2个，并且不在同一个电池片上；
目视+卡尺&callipers
a) on the solar cell, the air bubble area must not bigger 2 in every one square meter and can not be located in same solar cell.
b) 不在电池片上，气泡面积不大于8mm²，每平方米面积内
Copyright BYD Company Limited
检验标准 Standards
A 级（优质） A Grade(Excellent) B Grade(Appearance grade lower than grade A)
标准描述 Standard Description 面积1~10mm²数量≤3个。 Area1~10mm²，Quantity ≤3个.
划伤宽度0.2-0.5mm ，长度小于30mm ，每平方米面积内不多于3条。
The width between 0.2mm and 0.5mm，length smaller than 30mm，quantity of such scratch no more than 3/㎡
a) 电池片上，气泡面积小于4mm²，每平方米面积内不多于2个，并且不在同一个电池片上；
must smaller than 4mm²，quantity of such air bubble must no more than 2PCS/m²and can not be located in same solar cell；
1.1
钢化玻璃Glass
脏污 Dirty
1.2
钢化玻璃Glass
划伤 Scratch
组件内气泡及玻璃
1.3
钢化玻璃Glass
内气泡 Air bubble inside the solar panel or
Unaided eyes than 4mm²，quantity of such air bubble must not more than a) on the solar cell, the air bubble area
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066 the tempered glass
项目编号（可选）Item number
5 / 16
版本Version ：页 码Page ：数量不多于3；
than 8mm²，the quantity of such air bubble must no more than three in every one square meter. c) 距离玻璃边5mm 宽度之内不允许出现气泡
c) bubbles present within 5 mm of edge of glass is limited .d) 长度或直径小于1mm 的气泡小于10个/m²。 d) bubbles which’s length or diameter is bigger than 1mm,allow 10PCS/m²
b) 不在电池片上，气泡面积小于25mm²，b)Not on the solar cell, the air bubble area must not smaller than 25mm²，the quantity of such air bubble must no more than five in every one square meter；
c) 距离玻璃边5mm 宽度之内不允许出现气泡
c) bubbles present within 5 mm of edge of glass is limited .
d) 长度或直径小于1mm 的气泡允许10~15个/m²。
d) bubbles which’s length is bigger than 1mm,allow 10PCS/m²
a) 污垢不得引起内部短路，面积小于1cm²，每平方米内1~3个；
a)The dirty must not cause the internal short-circuit, the area must be less than 1cm²，the quantity of such dirty area must be no more than 5 in every one square meter. ；
b ）长度在10mm 内的毛发或毛发状异物允许数量2条以下，且出现的位置不允许可能导致短路或形成气泡通道。
b)Not on the solar cell, the air bubble area must not bigger 在1m²内不超过5个；
a ）组件内部允许存在长度或直径小于3mm 的异物，但是异物不得引起内部短路，每平方米面积内数量不多于1个。a ）The inside dirty length or diameter must be smaller than
1.4
钢化玻璃Glass
内部污垢Inside dirty
目视+卡尺&callipers
3 mm，and the dirty area can not cause the internal more than three in every one square meter.
b ）不允许毛发或金属类导电异物在电池片或汇流条处，以至于造成电池片短路。不允许在组件边缘出现毛发或毛发状异物以至于有形成气泡通道的危险。
Unaided eyes short-circuit, the quantity of such dirty area must be no
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
6 / 16
版本Version ：页 码Page ：
b ）Length within 10mm hair or hair-like foreign materials inside. Mustn’t result in internal short-circuit.
铝外框接缝处 The 2.1 juncture
of the aluminu m frames铝外框侧面 2.2 side of
aluminu m frame 铝外框背面 2.3 bottom of aluminu m frame 铝外框正2.4
面 Surface of
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：0个 area ≤4mm²，0pcs each module.
面积≤4mm²，每根边框数量≤2处 area ≤4mm²，quantity in each frame≤2
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤8mm²，每块组件允许的数量：≤3个 area ≤8mm²，quantity in each frame≤3.
面积≤8mm²，每根边框允许的数量≤2个 area ≤8mm²，quantity in each frame≤3
脏污 Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：0个 area ≤4mm²，quantity in each frame 0 .
面积≤4mm²、每根边框数量≤2个 area ≤4mm²、quantity in each frame≤2
脏污Dirty
目视+卡尺Unaided eyes &callipers
面积≤4mm²，每块组件允许的数量：≤1个 Dirty Area≤4mm²，Dirty area quantity 0.
面积≤4mm²，数量≤2个
dirty area≤4mm², Dirty Area Quantity≤2
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
7 / 16
版本Version ：页 码Page ：
aluminu m frame
a) 铝型材接缝配合良好，缝隙不超过0.35mm ； a) The clearance between the aluminum frames must be no more than 0.35mm.
b) 表面清洁干净，不得有字迹； handwriting.
c) 所有型材断缝处、安装口处不得有毛刺；
目视+卡尺+
铝外框组2.5
框 Aluminu m Frame
塞尺
划伤、间隙Scratch,cl earance
Unaided eyes ,calipers &feeling guage
c) The cross section or the installation hole of the aluminum frame must have no burr. d) 铝边框允许有不明显的轻微划伤； 正面划伤不允许有划破表面氧化膜；
侧面、背面划伤，宽度小于0.2mm ，长度小于10mm ； d) The slightly scratch which is not so obvious is allowed; the scratch on the top must not lacerate the oxidated film on the surface, the lacerated area at the rear and flank of the solar panel, width must be less than 0.2mm, length must be smaller than 10mm.
e) 组件长短边框安装上下错位≤0.5mm
e) The malposition (in upright direction) results from the installation of the long and short aluminum frame must be ≤0.5mm.
f) 模组边平行度没有在3mm 之内，模组的方形[（对角
Copyright BYD Company Limited
a) 铝型材接缝配合缝隙0.35mm-0.5mm ； a)The clearance between the aluminum frames 0.35mm-0.5mm； b) 表面清洁干净，不得有字迹； handwriting ；
c) 所有型材断缝处、安装口处不得有有可能引起人员伤害的毛刺；
c) The burr at the cross section and the installation hole can not hurt persons； d) 划伤有轻微刺破氧化膜；
划伤宽度0.2-0.5mm ，长度10-50mm ； 非线状擦伤，面积4mm²-100mm²，轻微刺破氧化膜。
d) lacerate the oxidated film slightly； the lacerating area, width 0.2-0.5mm，length between 10-50mm； none-linear scratch ,area between 4mm²-100mm²，slightly puncture the oxidated film。
e) 组件边框安装上下错位，不超过1mm ； e)The malposition(in upright direction)
b) The surface of the aluminum must be clean and has no b) The surface must be clean and no
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
8 / 16
版本Version ：页 码Page ：线1-对角线2）]/2大于1.5mm. 测量对 角线或者拐角的距离
modules [(Diagonal 1 – Diagonal 2))/2 is greater than 1.5 mm. Done by measuring Diagonal or distance between corners.
g) 流水孔错位
g) The malposition of the scupper
results from the installation of the aluminum frame must be no more than f) 模组边平行度没有在3mm 之内，模组的方形（对角线[1-对角线2）]/2大于1.5mm. 测量对
角线或者拐角的距离
f) Module sides are not parallel within 3 mm Squareness of modules [(Diagonal 1 – Diagonal 2))/2 is greater than 1.5 mm. Done by measuring Diagonal or distance between corners. g) 流水孔错位
g) The malposition of the scupper
f) Module sides are not parallel within 3 mm Squareness of 1mm ；
a) 组件正面边框与玻璃之间的隙宽度和深度测量，用厚度小于0.3mm 塞规检测。铝边框四角垂直方向塞规深入距离
封胶 3.1
Glue Sealing
封胶不可见 The glue must be invisible
目视+塞尺Unaided eyes & plug guage
a)Use the 0.3mm plug guage to measure the clearance between the top aluminum frame and the glass。At the direction of 45° to the 1mm depth slot aluminum frame, at the corner the plug guage can insert
b) 背板与边框不允许出现间隙
Copyright BYD Company Limited
a) 组件正面边框与玻璃之的间隙宽度和深度测量，用厚度小于0.3mm 塞规检测。铝边框四角垂直方向塞规深入距离
a)Use the 0.3mm plug guage to measure the clearance between the top aluminum frame and the glass。At the direction of 45° to the 1mm depth slot aluminum frame, at the corner the plug guage can
insert
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
9 / 16
版本Version ：页 码Page ：b)Sealant must excess out from the frame, no gap in bed of sealant.
the plug guage can insert
b)Sealant must excess out from the frame, no gap in bed of sealant.
接线盒 4.1 Junction
box
接线盒脏污 Dirty
目视 Unaided eyes
不允许接线盒上有硅胶
No silicon gel on the junction box. a) 硅胶溢出接线盒边缘3-7mm ；
a) The excess sealant width is within3-7mm, at the edge of the J-box
b) 盒内汇流条引出线TPT 开口完全被硅胶密封； b) The TPT clearance where the conflux belt go out must be completely sealed by the silicon gel. c) 二极管极性一致，数量方向正确；
c) The polarity of the diodes must be consistent, the quantity and the direction must correct. d ）汇流条表面干净、固定牢固
d ）The surface of the conflux belt is clean and be fixed stably.
不允许接线盒上有硅胶
No silicon gel on the junction box a) 硅胶溢出接线盒边缘3-7mm ； a) The excess sealant width is within3-7mm, at the edge of the J-box b) 不允许汇流条开口长度大于接线盒宽度； b) The cut width of the backsheet longer than width of the junction box, can’t accept. c) 二极管极性一致，数量方向正确； c) The polarity of the diodes must be consistent, the quantity and the direction must correct；
d ）汇流条表面干净、固定牢固。
d ）The surface of the conflux belt is clean and be fixed stably
a ）引出线需要有正负极标识；
a ）The cable must be marked with polarity b ）不允许公母头有损坏或正、负级接反现象；
接线盒外观
接线盒 4.2 Junction
Box
The appearan ce of the junction box
目视+卡尺Unaided eyes &callipers
接线盒 4.3 Junction
Box
引出电缆Cable
目视+卡尺Unaided eyes &callipers
a ）引出线需要有正负极标识；
a ）The cable must be marked with polarity. b ）不允许公母头有损坏或正、负级接反现象；
b ）The male/female connector must not be damaged or
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
10 / 16
版本Version ：页 码Page ：connected with wrong polarity.
c ）引出线和公母头上不允许有硅胶或脏污。 and have no silicon gel.
d ）公母头与标准公母头搭配组装，不能出现有松动或过紧的状况。
d ）The male/female connector must be installed with standard male/female connector, must not be too tight or loose.
b ）The male/female connector must not be damaged or connected with wrong polarity c ）The cable and the male/female connector must be clean and have no silicon gel
d ）公母头与标准公母头搭配组装，不能出现有松动或过紧的状况。
d ）The male/female connector must be installed with standard male/female connector, must not be too tight or loose a) 处于层压组件边缘的褶皱或折痕；介于电池片边缘和玻璃边缘之间的褶皱或折痕；处于接线盒与背板连接处的褶皱或折痕不允许存在
a)Wrinkles or folds at edge of laminate or between edge of cell and edge of glass or at junction box
b) 超过1mm 宽度的褶皱或折痕不允许存在 b)Wrinkles or folds greater than 1 mm in width
c) 覆盖范围超过组件面积的10%的褶皱或折痕不允许存在
c)Wrinkles cover greater than 10 % of
c ）The cable and the male/female connector must be clean c ）引出线和公母头上不允许有硅胶或脏污
a) 处于层压组件边缘的褶皱或折痕；介于电池片边缘和玻璃边缘之间的褶皱或折痕；处于接线盒与背板连接处的褶皱或折痕不允许存在
TPT 表面5.1 TPT
surface
Wrinkles/Folds 褶皱或折痕
目视+卡尺Unaided eyes &callipers
a)Wrinkles or folds at edge of laminate or between edge of cell and edge of glass or at junction box b) 超过1mm 宽度的褶皱或折痕不允许存在 b)Wrinkles or folds greater than 1 mm in width
c) 覆盖范围超过组件面积的10%的褶皱或折痕不允许存在 c)Wrinkles cover greater than 10 % of backsheet area d) 允许由于焊带引起的规则褶皱
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
11 / 16
版本Version ：页 码Page ：
backsheet area
背面有鼓包，单个面积不大于100mm²，高
鼓包面积不大于50mm²，鼓包高度不超过1mm ，每平方米面积内不超过1个，鼓包不得出现自组件边缘10mm 宽度
TPT 表面5.2 TPT
surface
鼓包Heave
目视+卡尺&callipers
的地方。
height must be no more than 1mm, the quantity of the the heave must not touch the edge of the solar panel. a) 异物引起的几种凹痕，包括处于层压组件边缘的凹痕；介于电池片边缘和玻璃边缘之间的凹痕；处于接线盒与背板连接处的凹痕。以上凹痕不允许存在
a)Indentations on backsheet from contact with object of foreign source (excluding components of processing
TPT 表面5.3 TPT
surface
凹陷Depresse d area
目视+卡尺&callipers
equipment) or improper equipment maintenance at edge junction box. Indentations mentioned can’t accept b) 层压过称中由异物或不恰当的设备引起的小于50mm 长度的凹痕≤3条
b)Indentations on backsheet from contact with object of foreign source (excluding components of processing equipment) or improper equipment maintenance less than
Copyright BYD Company Limited
度不超过2mm ，每平方米面积内个数不超过3个，鼓包不得出现在组件边缘10mm 宽度的地方。
the area of single heave must be no more than 2mm，the quantity must be no more than 3 in every one square meter。
Unaided eyes The heave area must be no bigger than 50mm²，the heave The heave at the rear of the solar panel,
heave must be no more than 2 in every one square meter, than100mm²，the height must be no more
凹陷面积100mm²-300mm²，深度2-3mm ，每平方米面积内数量不超过15个 depth 2-3mm，the quantity must be no more than 15 per square meter
Unaided eyes of laminate or between edge of cell and edge of glass or at The depressed area 100mm²-300mm²，
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
12 / 16
版本Version ：页 码Page ：50 mm in length
c) 层压过称中由异物或不恰当的设备引起的大于50mm 长度的凹痕不允许存在。
c)Indentations on backsheet from contact with object of foreign source (excluding components of processing equipment) or improper equipment maintenance less than 50 mm in length
允许表面擦痕，划伤无明显深度，不得划破表面T 层, 宽度小于0.1mm ，长度小于20mm ，每平方米面积内不多于1条。
Scrape on the surface is allowed to pass, the lacerating area has no obvious depth and must not damage the TPT, the width must be smaller than 0.1mm,the length must be smaller than 20mm, the quantity must be no more than1pcs per quare meter.
组件电池颜色均匀一致，颜色范围深蓝色、蓝色到淡蓝色，允许相近颜色存在，但不允许电池片跳色，如：从黑色到蓝
a. 划伤宽度0.1-0.5mm ，划伤长度不大于
50mm ；
a. The width of the lacerating area
between0.1-0.5mm ，length must be no bigger than 20mm； b. 划破TPT ，长度小于20mm. b. The TPT is lacerated with the length smaller than 20mm.
同一组件上电池片跳色色斑，同一电池片上有跳色色差。
The color change suddenly in one solar panel, the color change suddenly in one solar cell。
TPT 表面5.4 TPT
surface
划伤scratch
目视+卡尺Unaided eyes &callipers
电池片 6.1 Solar
cells
色差chromatis m
目视Unaided
eyes
色。
The color of the solar panel must be average and consistent, the color ranges from dark blue, blue to light blue, the color is a little different in different area is OK, if the color suddenly changes(from black to blue for
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
13 / 16
版本Version ：页 码Page ：example) is not allowed to pass the inspection.
a) 不允许有三角形缺口和尖锐形缺口。 a) Triangle indentation and sharp
a) 不允许有V 形缺口，对于非V 缺口的要求如下： a) V shape indentation is not allowed.
b) 组件电池片边缘崩边，长度≤2mm ，深度≤0.5mm(多晶≤1.0mm) ，每块组件数量≤2处；
depth ≤0.5mm(polycrystalline≤1.0mm) ，quantity ≤2. c) 四角缺口：尺寸≤1.5 mm×1.5mm，数量≤1处；
目视+卡尺&callipers
c)Four angles indentation：demension ≤1.5 mm×1.5mm，以上缺口崩边均不可过电极(主栅线、副栅线) ，每平方面积内数量少于2个；
All the chipping and indentation can not be touch the bar line(main bar line and smaller bar line), such defect quantity must be less than 2 in every one square meter. 主栅线±5mm内不允许出现缺口、崩边。 main bar line.
Unaided eyes quantity ≤1.
indentation is not allowed。
b) 电池边缘崩边和缺口，其长度≤5mm ，深度不超过边缘栅线，数量≤3处；
四角缺口：尺寸≤2mm×2mm，数量≤1处； 每个组件缺口崩边数量≤5个。 b) the chipping and the indentation at the edge of the solar cell,length≤5mm ，depth can not be over the bar line on the edge, quantity ≤3；
four angles indentation ：
dimension ≤2mm×2mm，quantity ≤1； stringy indentation ：length ≤15mm ，quantity ≤1；
The quantity of the chipping and c) 允许崩边、缺口、掉角电池片碎渣留在组件内，但不允许因此而使两片电池片、电池片到汇流条、电池片到边框形成连通。（两
Copyright BYD Company Limited
b)The chipping on the edge of the solar cell: length≤2mm ， 细长形缺口：长度≤15mm ，数量≤1处；
崩边、缺
电池片 6.2 Solar
cells
口、破角chipping, indentatio n, corner breaking
no chipping and indentation is allowed inside ±5mm of the indentation for each panel≤5。
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
14 / 16
版本Version ：页 码Page ：
片电池片之间的碎渣最多只能与一边电池或互联条连通，与另一边电池距离必须大于0.2mm
c)The broken bits result from chipping, indentation and corner breaking can be in the solar panel, but can not conduct the solar cell, conflux belt with other solar cell, aluminum frame or conflux belt (the broken bits between two solar cells can touch one of the cells but must be away from another cell for more than 0.2mm)
栅线清晰，断栅长度≤2mm ，同一电池片上断栅累计长度不
电池片 6.3 Solar
cells
电池栅线Solar cell bar line
目视+卡尺&callipers
超过10mm ，不能允许有相邻的断栅存在
break off bar lines must be no more than 10mm,different bar lines must not be neighbouring from each other. a) 电池片的排列基本均匀，片间距为1.6mm ～3.5mm.
电池片排
电池片 6.4 Solar
cells
列 Solar cell collocatio n
目视+卡尺&callipers
串间距2mm ～4mm 。
Unaided eyes between solar cells and the distance between solar cell
strings range in 1.6mm～3.5mm.
And the distance between solar cell strings range in 2mm ～4mm.
Copyright BYD Company Limited
同一电池片上断栅累计长度20-30mm ； 允许有相邻断栅。
The bar line length≤2mm ，the total length of the break off bar lines must be 20mm-30mm,different bar lines can be neighbouring from each other. a ）片间距、串间距1.6-4.0mm
a) the distance between solar cells and the 1.6mm ～4mm.
And the distance between solar cell strings range in 1.6mm～4mm.
b ）边框内侧到电池片的间距＞3mm 。
Unaided eyes The bar line is clear,length≤2mm ，the total length of the
a)The collocation of the solar cells is average, the distance distance between solar cell strings range in
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
15 / 16
版本Version ：页 码Page ：b ）边框内侧到电池片的间距9±2mm 。
b ）The distance from aluminum to solar cell9±2mm. c ）边框内侧到汇流条的间距≥6mm 。
c ）The distance from aluminum to conflux belt≥6mm d) 焊带露白宽度≤0.3mm ，每片电池片上主栅线露白长度不d) The naked area of the siliver pole≤0.3mm. length not longer than 150mm
b ）The distance from aluminum to solar cell＞3mm.
c ）边框内侧到汇流条的间距＞3mm 。 c ）The distance from aluminum to conflux belt ＞3mm
d) The naked area of the siliver pole ≤0.5mm 。
电池片存在可视裂纹, 裂纹长度小于电池片长度的1/3，裂纹和它的延长线造成失效面积≤10%，组件IV 曲线无异常
The visible crack on the cell, its length is less than 1/3 of the length of the solar cell, the invalid area on the solar cell results from crack and its extended line must be smaller than≤10%，the IV curve of the solar panel has no abnormal
超过50mm ，每块组件电池片主栅线露白总长度≤150mm 。d ）焊带露白≤0.5mm ；
电池片裂
电池片 6.5 Solar
cells
纹、隐裂Solar cell crack and invisible crack
目视 Unaided eyes
电池片不存在任何裂纹
No crack( visible or invisible) on the solar cell.
IV 曲线异
7.1
IV 测试 IV Test
常 IV Curve Abnormal
8.1
标签 Label
铭牌Nameplat e
测试仪+目视
tester &Unaided eyes 目视+卡尺Unaided eyes & callipers
按照图纸要求
Refer to the standard drawing.
I-V 曲线平滑没有台阶
I-V curve is smooth and has no step.
I-V 曲线有台阶 I-V curve has step
Copyright BYD Company Limited
★秘密★
文件名称： File name: 文件编号 File number:
BYD 光伏组件出货检验标准
BYD PV Modules shipment inspection standard
2M SOP0004066
项目编号（可选）Item number
16 / 16
版本Version ：页 码Page ：
a) 边框条码与组件玻璃内条码一致；
a) 边框条码与组件玻璃内条码一致；
8.2
标签 Label
条形码 Bar code
目视 Unaided eyes
a) The bar code of the aluminum frame must be consistent with the bar code under the glass.
b ）清晰可以识别，粘贴端正、无褶皱、无翘起。 b ）Clear and easy to recognize, no tilt and deflection.
a) The bar code of the aluminum frame must be consistent with the bar code under the glass；
b ）清晰可以识别，粘贴端正、无褶皱、无翘起。
b ）Clear and easy to recognize, no tilt and deflection.
8.3
标签 Label 功率要求8.4
Power requirem ent 8.5
物料 Materials 物料 Materials
接地标识Grounding mark 电性能参数 I-V data 物料 Materials 连接器Connector
目视 Unaided eyes
接地标识位置正确
The grounding mark must be in the correct position.
接地标识位置正确
The grounding mark must be in the correct position.
太阳能模拟器Simulator 依照BOM Check by BOM 连接器型号 The type of the connector
出货要求：按照各项目太阳能电池组件客户需求信息表要求，平均功率正偏差。 Shipment requirement: According to the table of every client, average positive deviation.
原材料与工艺工程师提供的BOM 清单一致。
Materials according to BOM which approved by technologist. 参考各项目太阳能电池组件客户需求信息表。 According to the table of every client.
8.6
8. 包装根据BYD 标准品或客户指定包装要求进行包装。
Package should accord to BYD standardized mode of product package or customers’ requirements
Copyright BYD Company Limited